Back to Mike's Clock Clinic's Main Web Page

Back to the Motors and Rotors Page

I've noticed several "rebuilders" poping up on the Internet and these rebuilders are cheaper.  If you look closely they do NOT warranty their work.  I have and always have warrantied my work for two full years.

For pricing on NOS (new old stock) aluminum rotors and charges for rebuilding your specific rotor or motor,
please see The Motors and Rotors Page.

Here is a Web page with some of the steps illustrated with pictures.   Repair Illustration

GE, Herschede, Revere, & Telechron Rotor, Motor & Coil Repair and Information Page.

Copyright © 1998-2012 by Michael P. Murray & Mike's Clock Clinic

Mike's Clock Clinic
17000 Western Avenue # 7
Gardena, CA   90247-5262

Phone: 310-225-5645, or 877-286-6762 (Toll Free)

E-mail address: Mike@atmos-man.com
MCC's Web site is located at http://www.atmosman.com



Index of Motor and Rotor & Resources by Category:






Telechron Rotors by Sequential Numbers



All Telechron rotors are no longer in production from ANY source.  I have many rotors
rebuilt and in stock.  Any rotor that is not in my stock I can rebuild even the
aluminum ones.

Any rebuilt Telechron "B" rotor can have any shaft you'd need.  Once I
open up a "B" rotor I can install any configuration of shaft or pinion.

The Telechron rotors that I sell at: http://www.atmosman.com/rotor.html , are the copper
and nickel rather than the aluminum that were made from the early 1970's.
I don't list or sell any 50 cycle rotors.

There is a great book on the subject of Telechron/G.E. clock and it's called,
"Electrifying Time" by Jim Linz.  Please be aware that the procedure described
in the book as "New Life into Dead Rotors" is flawed.  The reason is that he
suggests using lacquer thinner.  Lacquer thinner will slowly destroy phenolic
wheels, which are employed in all Telechron rotors.

The Telechron "B" rotor was in production as early as 1919 and, the "B-3" has
the greatest torque followed by the "B-2".

The "M" number of the rotor was Telechron's way of identifying the customer
and not the rotor.  It has some significance in "B" rotors but all 3.6 rpm "H's"
have the same torque.

Listing of Telechron Rotors by their "M" #




Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-1 	B-2	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion)	2 watts
M-1	B-2	1	1/8x1/2 With 9-Tooth Gear (Pinion)	2 watts
M-2 	B-2	1					2 watts
M-4	B-2	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion)	2 watts
M-5	B-2	1	18-Tooth Gear (Pinion)		2 watts
M-11	B	4	1/8x1/2 Solid Round
M-11	B	1	1/8x1/2 Solid Round with Flat
M-12	B-3	1	12-Tooth Gear (Pinion)		4 watts
M-12	B-3	1	1/8x1/2 Solid Round with Hole in shaft	4 watts
M-14	B-3	60	9-Tooth Gear (Pinion)		4 watts
M-15	B-3	1	Long shaft, Long pinion, Hold end
M-16	B-3	1	1/8x1/2 Solid Round with Flat	4 watts
M-31	B-3	1	1/8x1/2 Solid Round with Flat	4 watts
M-38	B-2	1	1/8x1/2 Solid Round with Flat	2 watts
M-45
M-48	B-2	1					2 watts
M-60	B	1	1/8x1/2 Solid Round with Flat
M-99 	B        1                                         8 watts
M-103	B	4	1/8x1/2 Solid Round with Flat
M-150	B-3	60	1/8x1/2 Solid Round
M-163	B	4	1/8x1/2 Solid Round with Flat
M-165	B-3	1	1/8x1/2 Solid Round		5 watts
M-168 	B-3	1	1/8x1/2 Solid Round With Hole on the side of the Shaft	4 watts
M-168	B-3	1	1/8x1/2 Solid Round		4 watts

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-195 	B	4	1/8x1/2 Solid Round with Flat
M-209 	B-3	1	1/8x1/2 Solid Round with Flat               4 watts
M-211 	B-2	1	1/8x1/2 Solid Round With Hole on the side of the Shaft
M-216	B-2      1      1/10x1/2 Hole With 11-Tooth Gear (Pinion)
M-217	B-2      1        1/8x1/2 Hole With 9-Tooth Gear (Pinion)	2 watts
M-220	BMX	1	1/8x1/2 Solid Round with Flat (Takes two fields and coils)	4 watts
M-220	BMX	1	1/8x1/2 Solid Round (Takes two fields and coils)	4 watts
M-245	B-2	1	Extra long shaft with hole end and 9-Tooth Gear (Pinion)
M-348	B
M-454 	B
M-519	F-1	3.6	10-Tooth Output Gear (Pinion)
M-538 	B	1	1/8x1/2 Solid Round
M-547	B-2     1       5/32" Reverse threaded shaft    5 watts
M-579 	H	3.6	10-Tooth Output Gear (Pinion)
M-583	B-2	1	1/8x1/4 Solid Round		2 watts
M-591	B-2	1	1/8x1/2 Solid Round
M-615
M-625	B
M-639	B-6	1	12-Tooth Output Gear (Pinion)
M-667 	F-1     3.6     10-tooth Output Gear (Pinion)
M-714	H	3.6	10-Tooth Output Gear (Pinion)
M-768 	H	3.6	10-Tooth Output Gear (Pinion)
M-776	B-8	1	1/8x1/2 Solid Round
M-808 	B-9	60	1/8x1/2 Solid Round		5 watts
M-810	B-9	1	1/8x1/2 Solid Round		5 watts
M-861 	B-9	1	1/8x1/2 Solid Round		5 watts
M-892
M-959 	B-8	1
M-1000	B-3	30	1/8x1/2 Solid Round		5 watts
M-1001 	B-F	1	36-Tooth Output Gear (Pinion)
M-1024	B-F	1	36-Tooth Output Gear (Pinion)
M-1028	B	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion)
M-1038	B-3	3	1/8x1/2 Solid Round
M-1040
M-1145	H	3.6	10-Tooth Output Gear (Pinion)

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-1162	B	1	1/8x1/2 Solid Round with Flat
M-1181	B-2	1	Threaded Output Gear (Pinion)
M-1198	H		Output Gear (Pinion)
M-1223	B-3	1	1/8x1/2 Solid Round With Hole on the side of the Shaft
M-1228 	B-3	1	1/8x1/2 Solid Round With Hole on the side of the Shaft
M-1308
*M-1313 H-3	3.6	10-Tooth Output Gear (Pinion)
*M-1321	H-3	3.6	10-Tooth Output Gear (Pinion)
M-1343 	H		Output Gear (Pinion)
M-1379	B-F	1	18-Tooth Output Gear (Pinion)
M-1386  B-3     6       1/8x1/2 Solid Round with Flat       4 watts
M-1417
M-1432	H		Output Gear (Pinion)
M-1444  B-2    1     10-Tooth Output Gear (Pinion)
M-1449
M-1475	B-2	1					12 watts
M-1486	B-8	1	1/8x1/2 Solid Round		2 watts
M-1519 	H	3.6	10-Tooth Output Gear (Pinion)
M-1525	B		1/8x1/2 Solid Round
M-1583 	B-7	1	1/8x1/2 Solid Round
M-1605	B-9	60	1/8x1/2 Solid Round		5 watts
M-1630 	H-3	3.6	10-Tooth Output Gear (Pinion)
M-1631	H	3.6	10-Tooth Output Gear (Pinion)
M-1664
M-1672
M-1676	H		Output Gear (Pinion)
M-1678	H	3.6	10-Tooth Output Gear (Pinion)
M-1694  C-5      1      12-Tooth Output Gear (Pinion)               6 watts
M-1710	B-2	1		                           2 watts
M-1721	B-9	1	1/8x1/2 Solid Round
M-1726	B-3	1	1/8x1/2 Solid Round
M-1726	B-3	1	1/8x1/2 Solid Round With Hole on the side of the Shaft
M-1747	B-8	1	1/8x1/2 Solid Round		2 watts
M-1778	B-8	1	1/8x1/2 Solid Round
M-1794	B-C	60	1/8x1/2 with 10 tooth pinion .35" length	6 watts
M-1801
M-1806	B	60	1/8x1/2 Solid Round
M-1809  B-3       4       1/8x1/2 Solid Round with Flat       4 watts
M-1812	B	60	1/8x1/2 Solid Round
M-1816
M-1830	B	1	1/8x1/2 Solid Round
M-1960  B-3          1                                       4 watts
M-2017	B-3	1	1/8x1/2 Solid Round With "I" Shaft at end

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-2023	H	3.6	10-Tooth Output Gear (Pinion)
M-2028
M-2034  H-5      1/60
M-2038	B-9	30	1/8x1/2 Solid Round		5 watts
M-2052	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2055	B-C	4					4 watts
M-2056
M-2060
M-2066
M-2070
M-2074
M-2088
M-2106
M-2124	B-F	1	36-Tooth Output Gear (Pinion)
M-2135	B-15		Output Gear (Pinion)
M-2146	H	3.6	10-Tooth Output Gear (Pinion)
M-2150
M-2184	B		1/8x1/2 Solid Round
M-2200	B-3	4	1/8x1/2 Solid Round	(Used in Nutone 20 volts, 4 watts)
M-2205
M-2229	B-15		Output Gear (Pinion)
M-2244	B-3	1	1/8x1/2 Solid Round
M-2260 	B-2	1	1/8x1/2 Solid Round
M-2269
M-2270
M-2275	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2309 	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2317	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2319	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2322	H	3.6	10-Tooth Output Gear (Pinion)
M-2327	H	3.6	Output Gear (Pinion)
M-2334	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2337	B	1
M-2347	H		Output Gear (Pinion)
M-2360
M-2370
M-2374	B-2	1	Threaded Output Gear (Pinion)
M-2375	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2376 	B-2	1	Threaded Output Gear (Pinion)
M-2377	B-3	1	1/8x1/2 Solid Round with Flat	4 watts
M-2378

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-2379
M-2381 	B-3	1	12-Tooth Output Gear (Pinion)
M-2387	B
M-2394 	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2396	H	3.6	10-Tooth Output Gear (Pinion)
M-2397	B-2	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion)
M-2397	B-2	1	1/8x1/2 Hole Round
M-2398 	H	3.6	10-Tooth Output Gear (Pinion)
M-2401	B-2	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion)
M-2405
M-2409	B		1/8x1/2 Solid Round
M-2431 	B
M-2432
M-2440
M-2442	B-15		Output Gear (Pinion)
M-2445 	B-15		Output Gear (Pinion)
M-2451	B-14	1	1/8x1/2 Solid Round
M-2453	B
M-2457
M-2475	H	3.6	10-Tooth Output Gear (Pinion)
M-2481	B-13	1	1/8x1/2 Solid Round		5 watts
M-2484	B	4	1/8x1/2 Solid Round
*M-2487 H-3	3.6	10-Tooth Output Gear (Pinion)
M-2492	S-1	3.6	Output Gear (Pinion) (Aluminum)
M-2497
M-2501
M-2510 	B-3	1	1/8x1/4 Solid Round		4 watts
M-2510 	B-3	1	1/8x1/2 Solid Round		4 watts
M-2510 	B-3	1	1/8x1/2 Solid Round With Hole on the side of the Shaft	4 watts
M-2515	B-2	1	1/8x1/2 Hole Round
M-2515	B-2	1	1/8x1/2 Hole Round with Hole end
M-2516
M-2518	B-F	1	36-Tooth Output Gear (Pinion)
M-2519 	B-F	1	18-Tooth Output Gear (Pinion)
M-2525	B	2	1/8x1/2 Solid Round
M-2528
M-2529	B-3	4	1/8x1/2 Solid Round
M-2535	B-C	60	1/8x1/2 Solid Round
M-2538	BMX	1	1/8x1/2 Solid Round (Takes two fields and coils)

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-2565	B	60	1/8x1/2 Solid Round
M-2587	B-C	60	1/8x1/2 with 10 tooth pinion .35" length	6 watts
M-2604	B	60	1/8x1/2 Solid Round
M-2613	B	1	1/8x1/2 Solid Round
M-2614	B-3	1	1/8x1/2 Solid Round                     4 watts
M-2636	B-3	1	1/8x5/32 Solid Round with Short Shaft	4 watts
M-2636	B-3 1		Output Gear (Pinion)
M-2644	B-3	1
M-2653	B-3	1	1/8x1/2 Solid Round
M-2667
M-2670	B
M-2675 	B-F	1	36-Tooth Output Gear (Pinion)
M-2676	H-3	3.6	10-Tooth Output Gear (Pinion)
M-2679 	B-13	30	1/8x1/2 Solid Round			5 watts
M-2682	H	3.6	10-Tooth Output Gear (Pinion)
M-2687 	H-7	1	Round
M-2690 	H-7	2	Round
M-2692 	H-7	3	Round
M-2698 	H-7	6	Round
M-2700	C-5      1   16-Tooth Output Gear (Pinion)               6 watts
M-2703   C-5     2                                               6 watts
M-2706   C-5     4                                               6 watts
M-2709   C-5
M-2712	C-5	1                                              6 watts
M-2723
M-2726
M-2737 	B-3     60        1/8x1/2 Solid Round                         6 watts
M-2738	B-3	1	1/8x1/2 Solid Round
M-2738	B-3	1	1/8x1/2 Solid Round With Hole on the side of the Shaft
M-2776	C-5	1	16-Tooth Output Gear (Pinion)               6 watts
M-2782 	B-C	60	9-Tooth Output Gear (Pinion)
M-2790	B-3	30	1/8x1/2 Solid Round			5 watts
M-2835 	B-11	1	1/8x5/16 Output Gear (10 tooth Pinion)
M-2860
M-2864  B-3                                              4 watts
M-2934 	B-13	0.5						4 watts
M-3019	B-2	1	3/32x1/2 Hole with 10 tooth gear (Pinion)
M-3025 	H-10	3.6	10-Tooth Output Gear (Pinion)
M-3042	H-10	3.6	10-Tooth Output Gear (Pinion)		4 watts
M-3046	B-15		Output Gear (Pinion)
M-3047	B-15		Output Gear (Pinion)
M-3069	B-2	1	1/8x1/2 Solid Round

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-3072	S	3.6	Output Gear (Pinion) (Aluminum)
M-3083	S	3.6	Output Gear (Pinion) (Aluminum)
M-3084
M-3097	H	3.6	10-Tooth Output Gear (Pinion)
M-3103	H		Output Gear (Pinion)
M-3107	B	1	1/8x1/2 Solid Round
*M-3110	 H-3	3.6	10-Tooth Output Gear (Pinion)
M-3126	B	1	1/8x1/2 Solid Round
M-3130
M-3136 	H	3.6	Output Gear (Pinion)
M-3140	C-5	1	16-Tooth Output Gear (Pinion)
M-3141	S	3.6	Output Gear (Pinion) (Aluminum)
M-3150	H-18	3.6	10-Tooth Output Gear (Pinion)
M-3151	H-18	3.6	10-Tooth Output Gear (Pinion)
M-3154 	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3156	S	3.6	Output Gear (Pinion) (Aluminum)
M-3162 	S	3.6	Output Gear (Pinion) (Aluminum)
M-3163	B	60	1/8x1/2 Solid Round
M-3178 	BC-3	30	1/8x1/2 Solid Round
M-3186
M-3191 	B-13	1	1/8x1/2 Solid Round			5 watts
M-3210	B-13	30	1/8x1/2 Solid Round			5 watts
M-3215 	B	60	1/8x1/2 Solid Round
M-3218	H-3	14.4	17-Tooth Output Gear (Pinion)		2 watts
M-3230 	H	3.6	Output Gear (Pinion)
M-3235	BC-3	60	1/8x1/2 Solid Round (Aluminum)		6 watts
M-3243 	S-4	3.6	15-Tooth Output Gear (Pinion) (Aluminum)
M-3296	S	3.6	Output Gear (Pinion) (Aluminum)
M-3310 	S-4	3.6	15-Tooth Output Gear (Pinion) (Aluminum)
M-3313	S-4	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3326 	S	3.6	Output Gear (Pinion) (Aluminum)
M-3327	S-4	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3331	S	3.6	Output Gear (Pinion) (Aluminum)
M-3333 	S	3.6	Output Gear (Pinion) (Aluminum)
M-3373	BMX      1        1/8x1/2 solid round 10-Tooth Output Gear (Pinion)
                            (Takes two fields and coils)
M-3378 	S-5	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3388	B-16	1	1/8x1/2 Solid Round
M-3394 	S	3.6	Output Gear (Pinion) (Aluminum)
M-3395	S	3.6	Output Gear (Pinion) (Aluminum)
M-3400 	S	3.6	Output Gear (Pinion) (Aluminum)

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-3401	H-3	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3403 	H		Output Gear (Pinion)
M-3404	S-5	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3413 	B-16	1	1/8x1/2 Solid Round
M-3420	B-15		Output Gear (Pinion)
M-3420 	H	3.6	10-Tooth Output Gear (Pinion)
M-3424	H	3.6	10-Tooth Output Gear (Pinion)
M-3473 	H-3	14.4    17-Tooth Output Gear (Pinion) (Aluminum)	2 watts
M-3476	S	3.6	Output Gear (Pinion) (Aluminum)
M-3479	S	3.6	Output Gear (Pinion) (Aluminum)
M-3481 	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3485	H		Output Gear (Pinion)
M-3486	S	3.6	Output Gear (Pinion) (Aluminum)
M-3497	H	3.6	10-Tooth Output Gear (Pinion)
M-3499 	H	3.6	10-Tooth Output Gear (Pinion)
M-3502	B	1	1/8x1/2 Solid Round
M-3504 	B-16
M-3506	B-13	1	1/8x1/2 Solid Round (Aluminum)
M-3506 	B-13	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion) (Aluminum)
M-3508	S	3.6	Output Gear (Pinion) (Aluminum)
M-3509  S-1     3.6     9-Tooth Output Gear (Pinion) (Aluminum)
M-3514
M-3515 	B	0.5	1/8x1/2 Solid Round
M-3518
M-3520 	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3522	S	3.6	Output Gear (Pinion) (Aluminum)
M-3524 	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3528	S	3.6	Output Gear (Pinion) (Aluminum)
M-3533 	S	3.6	Output Gear (Pinion) (Aluminum)
M-3536	B-13	1	1/8x1/2 Solid Round with Flat (Aluminum)
M-3538 	B-15		10-Tooth Output Gear (Pinion)
M-3542	B-15    1	10-Tooth LONG Output Gear (Pinion) (Aluminum)  4 watts
M-3545 	B	1	1/8x1/2 Solid Round
M-3546	B-13	2	1/8x1/2 Solid Round (Aluminum)      4 watts
M-3548 	B	4	1/8x1/2 Solid Round
M-3556	B-15		Output Gear (Pinion)
M-3575 	BC-3	60	1/8x1/2 Solid Round (Aluminum)  6 watts
M-3580	BC-3	60	1/8x1/2 Hole With 9-Tooth Gear (Pinion) (Aluminum)  6 watts
M-3583	BC-3	60	1/8x1/2 Solid Round (Aluminum)  6 watts

Number	Type	RPM	Shaft & Description	Wattage  [If known]

M-3584
M-3586	B	57.6	1/8x1/2 Solid Round
M-3595 	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3609	B-13	1	1/8x1/2 Hole With 9-Tooth Gear (Pinion) (Aluminum)
M-3609 	B-13	1	Round with Gear (Pinion) (Aluminum)
M-3610	B		1/8x1/2 Solid Round
M-3614 	H	3.6	10-Tooth Output Gear (Pinion)
M-3617	H	3.6	10-Tooth Output Gear (Pinion)
M-3619 	S	3.6	Output Gear (Pinion) (Aluminum)
M-3628 	H-18	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3630	H	3.6	Output Gear (Pinion)
M-3632 	H-3	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3633	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)
M-3634	S	3.6	Output Gear (Pinion) (Aluminum)
M-3635	S-1	3.6	10-ToothOutput Gear (Pinion) (Aluminum)
M-3637 	S-1	3.6	10-Tooth Output Gear (Pinion) (Aluminum)	3 watts
M-3639	S	3.6	Output Gear (Pinion) (Aluminum)
M-3641 	S-1	3.6	Output Gear (Pinion) (Aluminum)
M-21003 EC-2       60      1/8x1/2 Solid Round with Flat



TYPE (B-?)   Measures  	1-1/4" in Diameter X 1-5/8" high
TYPE (H-?)   Measures	1-3/32" in Diameter X 7/8" high
TYPE (S-?)   Measures	1-1/16" in Diameter X 13/16" high
TYPE (C-?)   Measures	2-1/2" in Diameter X 2 1/16" high
TYPE (F-?)   Measures	2-3/16" in Diameter X 15/16" high

	The F has two screw holders built ring into the steel cast.
These "F's" were made during World War II in order to conserve copper.

* Some of these types were retrofitted to replace the F rotor.
(M-1313, M-1321, M-2487, & M-3110)
Return to Index


Information on the Rotor

The type of rotor (B-3, B-2, H-3, etc.),

TOP (This is significant because all rotors are self lubricating and the word TOP
must point straight up for the self lubrication to be its most efficient.)

The "M" # (M-1, M-31, M-38 etc.)

The RPM's of the rotor (RPM),

The current in cycles (CY),

A production number
Return to Index


Coil & Plate Information


Information on Telechron coils is intended as a user guide because many past
repair people just grabbed any coil that they could get there hands on and for
longer life of the clock and rotor, you should seriously consider replacing the
coil if your is not the proper wattage.

The "plate" over the back of the rotor has all the information you
need. This plate cover contains the following information:


  

    
      

        

          the "type" of rotor needed
          the volts (V)
          the current in cycles (CY)
        

        

          the Model # [either the clock or the movement, not
            sure] (MOV)
          the RPM's of the rotor (RPM)
          the wattage required (W)
        

      

      
All coils cost $100.00 plus the $10.00 shipping (Canada is $20.00), if that is all you order,
      otherwise the same shipping package can be used if you order the
      motor/rotor at the same time, so no additional shipping costs are
      necessary.
      


      Any coil of the same wattage will work but the inside diameter is slightly
      different for each and the tightest fitting coil will give the best results. 
      What I'm saying is that if you need a coil and the coil # is not legible then
      you should send the field and old coil and I'll find the best fitting good coil
      and return same.   The cost is the same $100.00 plus shipping.
      


      There is one exception and that is either the # 10 or the # 12 coil which are 24
      and 20 volts respectfully and can be used is any situation from 12 to 24 volts.
      These were typically used in clocks that were part of a door bell system like Nutone.
      Both the # 10 and the # 12 coil cost are $150.00 each plus shipping because
      they are very rare.

      
 
      

        

          
            
Wattage

          
            
Coil Number

          
            
Comments

        

      

      

        

          12
          37-W
          This would have two fields and coils.
        

        

          10
          10-W
          This is 24 volts for NuTone door bell systems.
        

        

          8
          48-W
          This would have two fields and coils.
        

        

          6
          37-W
           
        

        

          5
          45-W
           
        

        

          4
          90-W
          This is 220 volts
        

        

          4
          48-W
           
        

        

          4
          44-W
           
        

        

          3
          68-W
           
        

        

          2
          12-W
          This is 20 volts for NuTone door bell systems.
        

        

          2
          56-W
           
        

        

          2
          60-W
           
        

        

          2
          65-W
           
        

       

          2
          70-W
           
        

       

          2
          75-W
           
        

      

  



Return to Index

Payment via Pay Pal

You may also use Pay Pal by clicking on the link below.

You do NOT have to be a member of Pay Pal in order to issue a payment.

When you click on the Pay Pal link below, you must fill in the dollar amount once you are in Pay Pal.











You should realize that a Telechron coil will effectively replace the Hammond
with the same wattage considerations.
Return to Index


36 Tooth Pinion for Most "B" Chiming Clocks



Most Herschede, Revere, & Telechron chiming clocks take the "B" rotor
and attached to that rotor is a 36 tooth pinion.   These pinions are lost at a
far too great of a rate.   I have a small stock of these pinions, which are
guaranteed to be an exact replacement or your purchase price will be refunded
to you upon the pinion's return.

All 36 tooth pinions cost $50.00 plus $10.00 priority mail (Canada is $20.00)
and are guaranteed to fit and work properly, which brings your total cost to
$60.00.

If you want to send in the clock for pinion replacement, please be advised that
shipping will jump to $80.00 with everything else staying the same.  The increase
covers return shipping and insurance and includes my labor charge of $50.00 for
the replacement.

I'll not ship the pinion until I received payment, so in order to
expedite the transaction please enclose your payment .  I ONLY
accept money orders, certified checks, or company checks for payment
but repeat customers may use personal checks.  Normally
shipping takes place one week or so after I receive payment and thanks !

You may also use Pay Pal by clicking on the link below.

You do NOT have to be a member of Pay Pal in order to issue a payment.

When you click on the Pay Pal link below, you must fill in the dollar amount once you are in Pay Pal.











Return to Index


Fiber (Phenolic) Gears for Most Mastercrafters and Sessions Electrics


Most Mastercrafters and Sessions Electric clocks have a fiber (phenolic) gear,
which is driven by the motor.  These drive gears usually break at far too
great of a rate.  I have a small stock of these gears, which are guaranteed
to be an exact replacement or your purchase price will be refunded to you upon
the pinion's return.

All  Fiber gears cost $50.00 plus $10.00 priority mail (Canada is $20.00)
and are guaranteed to fit and work properly, which brings your total cost to
$60.00.

If you want to send in the clock for drive gear replacement, please be advised that
shipping will jump to $80.00 with everything else staying the same.  The increase
covers return shipping and insurance and includes my labor charge of $50.00 for
the replacement.

I'll not ship the drive gear until I received payment, so in order to
expedite the transaction please enclose your payment .  I ONLY
accept money orders, certified checks, or company checks for payment
but repeat customers may use personal checks.  Normally
shipping takes place one week or so after I receive payment and thanks !

You may also use Pay Pal by clicking on the link below.

You do NOT have to be a member of Pay Pal in order to issue a payment.
When you click on the Pay Pal link below, you must fill in the dollar amount once you are in Pay Pal.











Return to Index




What if the clock needs more service?


Sometimes the electric clock needs to be overhauled even thought all the electrical
parts are replaced.

Electric clocks and especially chiming electrics, will wear out and rebuilt rotor
or not they will not run or run accurately.  One quick check it to grab the
center of the minute hand with your fingers and see if it wobbles.  Meaning
that there should be a very slight amount of "up, down, or side to side" play.
If the "play" is greater than a mm or so then there is a good chance the movement
will have to be rebuilt in order for the clock to run properly.

If that's the case then please see: 
Electric Overhaul Fees page
Return to Index





Back to the Motors and Rotors Page

A service from, Mike Murray

E-mail address: Mike@atmos-man.com


Founder of Clocksmiths


A specialist in Atmos and 400-day clock repair.


Also, I overhaul most plug in electric clocks.
In continuous service since 04/01/1982.

Mike's Clock Clinic   Memberships: Clocksmiths & NAWCC 

17000 Western Avenue # 7

Gardena, CA   90247-5262



Phone:  310-225-5645, or 877-286-6762


My Web site is located at http://www.atmosman.com/


Main FTP site is located at

http://www.home.earthlink.net/~atmosman/earthftp.html


Copyright © 1998-2012 by Michael P. Murray & Mike's Clock Clinic


I, Mike Murray, make no claims as to the accuracy or completeness for the
Telechron rotor information.  But I have made every effort to make
sure that the information is accurate.  I was given this information many
years ago and have continually updated for accuracy.

Back to the Motors and Rotors Page


This page has been accessed a grand total of





 times


Created in December of 1998 and last updated January 01, 2012.